Advanced Stack - Revision history

4.225.241.78: /* Post 2.4 */

2005-12-22T16:18:07Z

‎Post 2.4

4.225.241.29 at 20:31, 21 December 2005

2005-12-21T20:31:16Z

Ollj: /* Pre 2.4 */

2005-12-21T18:54:01Z

‎Pre 2.4

Numsgil at 19:30, 18 September 2005

2005-09-18T19:30:49Z

66.91.138.35 at 03:41, 4 June 2005

2005-06-04T03:41:11Z

New page

'''Saving Values into the Stack'''
The Stack can be used as a means to save a value than retrieve it whenever necessary. The new dup operator allows the number to stay in the Stack continously

{code}
cond
*.robage 0 =
start
998 rnd 1 add
stopcond
*.refeye *.myeye !=
*.eye5 50 >
start
dup .tie store
stop
{code}

This will duplicate the value and also use it to tie. The same value can then be kept and re-used forever. To use it as part of a condition statement requires a solo "dup" gene.

'''Timing Actions with the Stack'''
Another more advanced use is to store a whole series of actions into the stack and then unstacking them in the following cycles.

{code}
cond
*.robage 0 =
start
50 .repro
314 .aimdx
10 .up
stop

cond
start
dup
stop

cond
0 >
' dup gene and 0 > not really needed in this case but helps to
' demo ability to sense the stack without destroying the information
start
store
stop
{code}

This will cause the bot to perform the above actions from bottom to top.
This could also be used for anything from MB reproduction to more accurate aiming.

--------------------------------------------------------------------------------

[[Stack]]

@@ Line 46: / Line 46: @@
 == Post 2.4 ==
-The stack no longer carries values between cycles, making many of these techniques less useful than they were preciously.
+The stack no longer carries values between cycles, making many of these techniques less useful than they were previously.
 [[Stack]]

@@ Line 4: / Line 4: @@
 The Stack can be used as a means to save a value than retrieve it whenever necessary. The new dup operator allows the number to stay in the Stack continously
- cond
+<pre>
- *.robage 0 =
+cond
- start
+*.robage 0 =
-rnd 1 add
+start
- stopcond
+rnd 1 add
- *.refeye *.myeye !=
+stopcond
- *.eye5 50 >
+*.refeye *.myeye !=
- start
+*.eye5 50 >
- dup .tie store
+start
- stop
+dup .tie store
 stop
 This will duplicate the value and also use it to tie. The same value can then be kept and re-used forever. To use it as part of a condition statement requires a solo "dup" gene.
 '''Timing Actions with the Stack'''
 Another more advanced use is to store a whole series of actions into the stack and then unstacking them in the following cycles.
+<pre>
- cond
+cond
- *.robage 0 =
+*.robage 0 =
- start
+start
 .repro
 .aimdx
 .up
- stop
+stop
-−
- cond
+cond
- start
+start
- dup
+dup
- stop
+stop
-−
- cond
+cond
 >
- ' dup gene and 0 > not really needed in this case but helps to
+' dup gene and 0 > not really needed in this case but helps to
- ' demo ability to sense the stack without destroying the information
+' demo ability to sense the stack without destroying the information
- start
+start
- store
+store
- stop
+stop
+</pre>
 This will cause the bot to perform the above actions from bottom to top.
 This could also be used for anything from MB reproduction to more accurate aiming.

@@ Line 1: / Line 1: @@
 '''Saving Values into the Stack'''
@@ Line 49: / Line 50: @@
 --------------------------------------------------------------------------------
 [[Stack]]